• (1) Lower Vent Window Hinge Spring (ST1-01973)
• (1) Lower Vent Window Pivot Mount Nylon Shoulder Washer (ST1-03015)
• (1) Lower Vent Window Pivot Mount Nylon Flat Washer (ST1-02431)
• (2) Vent Window Hinge to Frame Mount Rivets

The post Door Side Curtain Vent Window Lower Hinge Repair Kit, New appeared first on Corvette & Classic Car Parts Store.

• Upper Vent Window Pivot Mount Screws (2) (ST3-0045)
• Upper Vent Window Pivot Mount Nylon FW (2) (ST1-02431)
• Upper Vent Window Pivot Mount Screw LW(2) (ST3-0147)
• Upper Vent Window Pivot Mount Screw Hex Jam Nut (2) (ST1-03033)
• Lower Vent Window Pivot Mount Nylon Shoulder Washer (2) (ST1-03015)
• Lower Vent Window Pivot Mount Nylon FW (2) (ST1-02431)
• Vent Window Hinge to Frame Mount Rivets (16)
• (2) 8-32 x 7/16″ Slotted Round Head machine screws
• (2) 8-32 hex nuts
• (2) #8 lock washers with 9/32″ OD

The post Door Side Curtain Vent Window Hinge Repair Kit, New appeared first on Corvette & Classic Car Parts Store.

The post Gas Pedal Pivot Arm, Original. appeared first on Corvette & Classic Car Parts Store.

The post Brake & Clutch Pedal Arm Pivot Shaft Sleeve, New. appeared first on Corvette & Classic Car Parts Store.

• 50-52 Chevy w/Special equipment
• 53-54 Chevy 210 and Bel Air models.
• 53-55 Corvette

The post Steering Column Horn Contact Screw, New Set of 3. appeared first on Corvette & Classic Car Parts Store.

• 50-52 Chevy w/Special equipment
• 53-54 Chevy 210 and Bel Air models.
• 53-55 Corvette

The post Steering Wheel Horn Contact Plastic Insulator Sleeve, New Set of 3 appeared first on Corvette & Classic Car Parts Store.

• 50-52 Chevy w/Special equipment
• 53-54 Chevy 210 and Bel Air models.
• 53-55 Corvette

The post Steering Wheel Horn Contact Plastic Pivot Ring, New. appeared first on Corvette & Classic Car Parts Store.

We have now had 2 instances where the diameter of the “shoulder” area on these bolts was too large for 1954 Corvette’s. In each case, the 1954 cars were built early (one car was SN 300). In both of these early built 1954’s the diameter of the shoulder of the original bolt was 0.430″. So, please measure the diameter of your existing bolts to be sure our bolts are the right size for you. We actually had an original hinge pivot bolt with a 0.430″ diameter shoulder that we shipped to one of these 54 owners and it worked fine for his needs.

To support this also, we have a reproduction hinge assembly. We disassembled this hinge assembly and measured the diameter of the pivot bolt. The diameter of the shoulder of the pivot bolt on the reproduction assembly was 0.500″.  When this change in shoulder diameter occurred, we do not know. But, we did want to pass this on to you 53-57 owners.  If your original bolt has a 0.430″ (plus or minus) diameter shank, you will need to have these bolts machined down if you use your original hinges.

Still have questions? Great, contact us with your question and we will do what we can to answer you.

The post Hood Hinge Pivot Bolt, Pair New. appeared first on Corvette & Classic Car Parts Store.